用CUT_EACH_BUSH2 割多入块时割完一个入子会多出一个移位

zpan888 · 发表于 2022-7-27 20:21:00

如题

CUT_EACH_BUSH2 用这个割两个以上入块时，割完一个入块再割下一个入子时，他会先回上一个入子起始点再跑下一个入块
程式如下

N1002( ----- N1002 ----- )
G90G92X-2.1408Y-3.5645
G00X-2.1408Y-3.5645
M20
( ---- Cut 1 ---- )
EH42H18FH52
G41G01X-2.1408Y-2.0645
G01X-2.4408Y-2.0645
G01X-2.4408Y2.9355
G01X2.5592Y2.9355
G01X2.5592Y-2.0645
G01X2.2592Y-2.0645
G40G01X2.2592Y-2.5645
( ---- Cut ---- )
G90G92X2.2592Y-2.5645
EH41H17FH51
G41G01X2.2592Y-2.0645
G01X-1.6408Y-2.0645
M00
G01X-2.1408Y-2.0645
G40G01X-2.1408Y-2.5645
M21
M01
G00X0.Y0.M82（这里的G00移位是多余的。怎么解决）

M21
M01
G00X6.4496Y0.M82

N003( ----- N003 ----- )
G00X6.4496Y0.
G90G92X6.4496Y0.
M20
M90
EH30H8FH21
G42G01X7.0736Y0.624
EH31FH21
G02X5.8256Y-0.624I-0.624J-0.624  (R0.8825)
G02X6.6412Y0.8615I0.624J0.624  (R0.8825)
/M00E1
G02X7.0736Y0.624I-0.1916J-0.8615  (R0.8825)
G40G01X6.72Y0.2704
G01X6.4496Y0.F100.0
M21
M01
G00X4.3088Y-3.5645M82

qq417605181 · 发表于 2022-7-27 21:58:24

rapid_move = $,(@88!=56)?"M21",$,"M01",;$,(@88==9)?"M00",;,$,(@88==9)?g1:g0,;,#x,#y,(@B=@27),(@45=0),(@27=0),"M82",$,(@88!=98)?," ",;,$, 在这里是不是要加些什么指令让他识别-、。-????

zpan888 · 发表于 2022-7-27 20:33:17

rapid_move = $,(@88!=56)?"M21",$,"M01",;$,(@88==9)?"M00",;,$,(@88==9)?g1:g0,;,#x,#y,(@B=@27),(@45=0),(@27=0),"M82",$,(@88!=98)?," ",;,$,

在这里是不是要加些什么指令让他识别-、。-

929171718 · 发表于 2022-7-27 22:10:26

找个正常的后处理，将这段复制过来

qq417605181 · 发表于 2022-7-28 08:21:22

rapid_move = $,(@88!=56)?"M21",$,"M01",;$,(@88==9)?"M00",;,$,(@88==9)?g1:g0,;,#x,#y,(@B=@27),(@45=0),(@27=0),"M82",$,(@88!=98)?," ",;,$,

在这里是不是要加些什么指令让他识别-、。-????

qq417605181 · 发表于 2022-7-28 08:22:15

我帮你改，加qq吧

qq417605181 · 发表于 2022-7-28 08:22:40

我无偿帮你改，加qq吧

qq417605181 · 发表于 2022-7-28 08:23:27

我无偿帮你改，加！qq吧

平凡之生 · 发表于 2022-7-28 10:25:22

走G00的没什么影响

		自动登录	找回密码
密码			立即注册

[交流] 用CUT_EACH_BUSH2 割多入块时割完一个入子会多出一个移位